Risultati della ricerca
- ...a]] was the top model of [[Conklin]], with the name put on the nib and the body, produced in three version, a short vest pocket, a standard and senior seni492 byte (81 parole) - 09:32, 12 ott 2018
- ...[Condor]] but their [[celluloid]] has better quality, and they have on the body an engraved logo with a stylized crown.597 byte (97 parole) - 17:06, 12 feb 2012
- ...Special]], and was produced in various sizes and with round and hexagonal body, always [[button filler]]. In [[1934]] was introduced the [[piston filler]507 byte (78 parole) - 18:33, 6 gen 2015
- ...l cylinder that contains the same, which is accessed by unscrewing the pen body from the nib section.507 byte (86 parole) - 01:01, 11 set 2019
- ...revents it from closing if it has not been completely withdrawn inside the body of the pen.554 byte (97 parole) - 02:32, 13 ago 2019
- ...n elliptical in shape to allow a smaller width of the slot made on the pen body. Also in this case, in fact, the pressure is exerted through a lateral ope440 byte (78 parole) - 21:42, 27 ago 2019
- ...ate '20s pens had the conventional ''[[flat top]]'' shape with cylindrical body and flat ends, while the cap had an hard rubber head. The pens were produce564 byte (99 parole) - 18:07, 27 ott 2013
- ...ot]] 30 years later. The pen had no cap; the nib could be moved inside the body of the pen, through a side slider, and was protected by a closing lid that494 byte (86 parole) - 00:16, 23 gen 2013
- As with other systems that use the pen body as a reservoir, this also has the advantage of having a greater volume to c428 byte (78 parole) - 01:16, 21 dic 2018
- ...the nib is mounted on a mechanism that allows you to retract it inside the body of the pen. From this feature comes also the name of ''retractable'' with w573 byte (95 parole) - 21:47, 27 ago 2019
- ...a ''case back'' that covers the rear part (in relation to the nib) of the body of the pen. This element is not always present, as for many pens the back e492 byte (90 parole) - 21:02, 5 mar 2021
- ...the principle of the [[match-stick filler]] through two small holes on the body, which, when the pens are in theirs rest position, provide access to the pr529 byte (98 parole) - 01:54, 27 nov 2020
- ...allowing a greatest dimension of the tank; it was made with a transparent body covered by an opaque plastic cylinder with a regular series of etchings tha573 byte (94 parole) - 19:46, 10 ago 2012
- ...allowing a greatest dimension of the tank; it was made with a transparent body covered by an opaque plastic cylinder with a regular series of etchings tha581 byte (94 parole) - 22:13, 2 nov 2023
- ...inserted in the feeder and kept in a central position with respect to the body of the pen, which normally acts as a tank. During the compression phase, th479 byte (90 parole) - 01:13, 21 dic 2018
- ...was introduced the [[Novum]] model in two versions, with smooth or faceted body and cap, produced in a variety of different celluloid colors. The pen had a571 byte (99 parole) - 00:16, 23 gen 2013
- ...of the barrel, so it can be moved into writing position or returned to the body of the pen.526 byte (101 parole) - 01:33, 14 ago 2019
- ...ome and golden trim. The ''OLO'' logo was reported or on section or on the body.546 byte (98 parole) - 00:19, 27 nov 2020
- The barrel, or body is usually the largest part of a fountain pen. In modern cartridge filled p538 byte (95 parole) - 20:32, 16 dic 2018
- ...) at the end of the slit, and returned with the protruding part inside the body of the pen, on the bottom of the same. For the filling the lever was extrac575 byte (102 parole) - 02:08, 23 ago 2019
Vedi (precedenti 20 | successivi 20) (20 | 50 | 100 | 250 | 500).